Inground Pool Pump

Hayward 1/1.5HP In-Ground Swimming Pool Pump Motor Strainer Generic Replacemen

Hayward 1/1.5HP In-Ground Swimming Pool Pump Motor Strainer Generic Replacemen
Hayward 1/1.5HP In-Ground Swimming Pool Pump Motor Strainer Generic Replacemen
Hayward 1/1.5HP In-Ground Swimming Pool Pump Motor Strainer Generic Replacemen
Hayward 1/1.5HP In-Ground Swimming Pool Pump Motor Strainer Generic Replacemen
Hayward 1/1.5HP In-Ground Swimming Pool Pump Motor Strainer Generic Replacemen
Hayward 1/1.5HP In-Ground Swimming Pool Pump Motor Strainer Generic Replacemen
Hayward 1/1.5HP In-Ground Swimming Pool Pump Motor Strainer Generic Replacemen
Hayward 1/1.5HP In-Ground Swimming Pool Pump Motor Strainer Generic Replacemen

Hayward 1/1.5HP In-Ground Swimming Pool Pump Motor Strainer Generic Replacemen

UL Certification for motor, longer lasting than those without certification. C-Clip Connector allows for easy disengagement of strainer housing in a matter of seconds for. High performance, energy saving motor with stainless steel shaft could stand wear and tear.

High efficiency, low maintenance and reliability. Transparent cover helps to judge if the basket needs clean or not. Massive strainer basket holds extra capacity. 100% drip proof, heat-resistant double-sized seal for long motor life. Drain plug for easy maintenance of pump. Suggested Installation: 24"-26" sand filter and above-ground pools. Flow: 5555GPH1HP/ 6500 GPH1.5HP.

Temp: 104 Degree Fahrenheit (40 Degree Celsius). 1x 1HP/1.5HP Dual voltage Swimming Pool Pump. Our machine does not allow you to disassemble the cable. This product is the highest standard of UL certification. If you wire it yourself, the machine will not work properly.

Thank you for your cooperation. The Pump Pressure is low; The Pump loses Pressure after being energized; Pump is running, But no water coming out.

The pump head is not filled with water, causing the pump to run without water. During the installation process of the pump, the inlet and outlet pipes are not tightly sealed, and the air leaks inside the pump head.

During the operation, the air inside the pump head is pulled in, resulting in insufficient internal pressure, weak pump pressure, no pressure on the pump, no water. When pumping water, the pump head is filled with water; the pump head transparent cover is tightened; the water pumpinlet and outlet joints are installed, and the raw material belts are tightened when the pipes are installed to prevent air leakage at the joints of the pipes. Before pumping, the pump head should be filled with water.

Inlet and outlet joints wrapped around the raw material tape, beware of leaks. Tightening when installing the inlet and outlet, beware of leaks. The pump head transparent cover is tightened to prevent air leakage and water seepage.

The water pump motor enters water or pump operating environment is excessively humid, and causing the motor to short-circuit and burn. The pump prevents the inlet from entering the water and burns the motor. There is Water in The Pump. Our company carries out a full inspection (pumping) of the water pump, and it might result in some package still leave some water in it, It is normal. The Pump stop working suddenly. Our company's products are equipped with temperature protection device, when the motor temperature is too high, the temperature protection device will start, It will stop pump working, if the motor is shut down in the normal operation process , generally there is foreign matter inhalation in the pump, resulting in the impeller stuck, motor temperature rise , pump stop working. Clean up the waste inside the filter screen of the water pump regularly to prevent the waste foreign matter from flowing into the water pump to jam the impeller.

Disassemble the pump body, clean up the foreign matter on the back of the pump body to ensure that there is no foreign matter blocking the impeller, and re-assembly can be reused. The foreign matter of the pump impeller and the diffuser is matched with the foreign matter, causing the impeller to be stuck and cleaning the foreign matter.

B Damage caused by natural disasters, flood fire, lightning or pollution. C If item was opened, any parts removed or repaired by any unauthorized person. D If damaged parts are the TFT screen or the screen has less than 3 dead pixels.

The item "Hayward 1/1.5HP In-Ground Swimming Pool Pump Motor Strainer Generic Replacemen" is in sale since Tuesday, August 25, 2020. This item is in the category "Home & Garden\Yard, Garden & Outdoor Living\Pools & Spas\Pool Equipment & Parts\Pool Pumps". The seller is "mrl-7312" and is located in Wofford Heights, California. This item can be shipped to United States.

  • Brand: Hongmotor
  • MPN: Does not apply
  • Type: Pool Pump
  • Pool Type: In Ground &Above Ground
  • Horsepower: 1/1.5HP
  • Speed: Single-Speed
  • Custom Bundle: No
  • Model: Swimming Pool Pump
  • Qmax: 350/410 L/min
  • Hmax: 11/15.5 Meter
  • Dual voltage: 110-120V/220-240V
  • Frequency: 60HZ
  • Color: Black
  • Certification: UL Certification


Hayward 1/1.5HP In-Ground Swimming Pool Pump Motor Strainer Generic Replacemen